Guide

Backwater Valves in Ottawa: The Rules, the City Rebate and Upkeep

Last reviewed 12 November 2026.

A backwater valve is a gate on the sewer pipe that closes when the City's sewer backs up. Ottawa has required one in new homes since 2004 on the storm line and 2012 on the sanitary line. An older house can add one, and the City rebates up to $1,000 for an indoor sanitary valve, with a permit pulled first.

On this page
  1. What a backwater valve does
  2. Do all homes need a backwater valve?
  3. How to know if a house has a backwater valve
  4. Where should a backwater valve be installed?
  5. What the City pays toward a new valve
  6. The permit, the inspection and the rebate, in order
  7. Do backwater valves require maintenance?
  8. What a backwater valve will not stop
  9. Is a backflow preventer the same as a backwater valve?
  10. What to ask a plumber
  11. Who owns the pipe the valve sits on
  12. Common questions
Representative image: Residential plumber working beneath a kitchen sink
Representative image.

Everything below comes from the City of Ottawa's own pages, read on 12 November 2026. In the local build of this directory read that day, 24 firms were listed under plumbers Ottawa, and two of their listing descriptions name backwater valves among their work. The others may do it too, so ask.

What a backwater valve does

The City's protective plumbing FAQ describes it as a device on a sanitary or storm sewer lateral, the pipe from your house to the main under the street. Inside is a gate. Most of the time it lies open, parallel with the pipe, and your wastewater runs out past it.

When heavy rain, snowmelt or a blockage raises the water in the City's sewer, the City calls it surcharging. Water starts flowing back up the lateral, and that flow pushes the gate shut, across the pipe. Without a valve, the City says, the surcharge comes into the house through floor drains, sinks and toilets.

Sanitary or storm

The City describes two laterals. Its causes of basement flooding page says the sanitary lateral carries toilets, washers, dishwashers, showers and sinks, and the foundation drains usually run to the storm sewer through a storm lateral. A sanitary valve keeps sewage out. A storm valve stops the storm sewer pushing back into the foundation drains.

Older homes can differ. The same page says that in some, the foundation drains join the sanitary or combined sewer, or there are none, and the flooding risk there is generally from the sanitary or combined sewer. Newer infill in older areas may be connected the modern way. That is why the first question for a plumber is which pipes your house actually has.

Do all homes need a backwater valve?

New homes do. The City's backwater valve permit page says all new single, semi-detached, row house and townhome dwelling units in Ottawa require a backwater valve on the sanitary service lateral. The program FAQ puts dates on it: mandatory in new homes after 2004 for stormwater and after 2012 for sanitary.

The sanitary rule has a paper trail. The permit page says it followed many basement backups during heavy rain, and a review of storm and sanitary backwater valves done at City Council's request. Council approved Report ACS2010-ICS-INF-006, which amended the sewer design guidelines through Technical Bulletin ISD-2010-1 to make a sanitary valve mandatory in new home construction.

That rule is written for new construction. For an existing house, the City's route is its rebate program, which the application form calls voluntary, and the rebate's cut-off years match the two dates above.

How to know if a house has a backwater valve

Look between the last branch of your sewer line and the point where the pipe leaves through the foundation wall. The City's FAQ says a valve may look like a Y-shaped fitting, a wye, with the branch plugged and pointing upward. Some older homes had one added later, so the build year alone does not settle it.

  • Built after 2012: expect a sanitary valve, under the City's rule for new homes.
  • Built between 2004 and 2012: expect a storm valve; a sanitary one only if added.
  • Built before 2004: neither was required when it was built.
  • An outdoor valve, the FAQ warns, is most likely buried in the yard and could be several feet deep.

If you cannot find it, a plumber with a drain camera can. Our guide to what Ottawa plumbers charge lists the published prices for a camera inspection.

Where should a backwater valve be installed?

Inside the home, where it can be reached. The inspection tab of the City's permit page says the building inspector must confirm that a normally open backwater valve is installed on the sanitary building drain for each dwelling unit, under the Ontario Building Code, Division B, section 7.4.6.4.(2)(a)(b), and the CAN/CSA standards it references.

The same tab adds that the valve must sit within the dwelling unit and be accessible for inspection and maintenance. A valve sealed under a finished floor with no access would not meet that wording, which matters if you are finishing a basement. Our guide to permits for finishing a basement in Ottawa covers the rest of that job.

Outdoor storm valves exist, and the City rebates them. Its standard drawing for an exterior retrofit of a foundation drain valve is marked for use on an exception basis only, so expect a plumber to explain why the valve cannot go inside before proposing one in the yard.

What the City pays toward a new valve

The City's Residential Protective Plumbing program, on a page dated 23 October 2026, pays the lesser of its maximum or the cost of the work. These are its valve lines. The program also rebates sump pumps, which our guide to waterproofing prices in Ottawa sets out with the rest of the table.

City of Ottawa Residential Protective Plumbing program, backwater valve rebates, read 12 November 2026
ItemWhat it protectsHouse built beforeMaximum rebate
Indoor sanitary backwater valveThe sanitary lateral: sewage pushed back up floor drains, sinks and toilets1 January 2012$1,000
Indoor storm backwater valveThe storm lateral, which usually carries the foundation drains1 January 2004$1,000
Outdoor storm backwater valveThe storm lateral, outside the foundation1 January 2004$2,500
Building permit (plumbing work only)The permit the installation needsFollows the device100 per cent of the fee

The City's fee schedule lists a permit for plumbing work only at $117 per application, and the program refunds that fee in full. The table gives a maximum for each item and states no overall cap. Figures quoted in Ottawa social media threads on page 1 for this search, a $3,000 cap and a $1,500 grant, do not match it.

Who qualifies

  • A residential unit inside the City of Ottawa.
  • Built before 1 January 2012 for the sanitary valve, before 1 January 2004 for a storm valve.
  • The device was not installed by the City.
  • The device is new. Maintenance, repair and replacement of an existing valve earn nothing, and the form adds "regardless of the condition of the devices".

The form also says the City rebates up to the amounts in force on the date the building permit is issued, so the permit date fixes your numbers.

The permit, the inspection and the rebate, in order

  1. Choose a licensed professional. The program's next steps say to select one or more licensed plumbers or contractors, and to discuss device options with them before you begin.
  2. Get the building permit before any work. The City's July 2026 advisory asks for a complete set of legible plans drawn to scale: floor plans for every storey in the work, with dimensions; the location, type, make and model of each device; a completed Schedule 1 for designer information, where it notes qualification exemptions may apply; and the rebate documents if you are applying. The permit page gives five business days for a first review of a house, and applications go in online through My ServiceOttawa or at a Building Code Services counter.
  3. Book the inspection. The permit page asks for 48 hours' notice. The plans must be on site, and the inspector's name and number are on the permit. Where there is a storm valve too, the sanitary valve inspection can be combined with the storm one at the underground rough-in and final interior stages.
  4. Pay the invoice in full. The form says invoices must be paid before you apply.
  5. Apply. The online form asks for your tax roll number and five uploads, each a .jpg, .png, .docx or .pdf of 2 MB or less: proof of ownership (a deed, land transfer or property tax bill), the permit with its receipt, the contractor's itemized invoice showing payment in full, the Building Code Services inspection report, and an electrician's report only if a sump pump runs on a whole home generator. Paper applications go to any Client Service Centre, the Permit Desk at 951 Clyde Avenue N, or by mail to Residential Protective Plumbing, City of Ottawa, 951 Clyde Avenue N, Ottawa, ON K1Z 5A6.

Mind the deadline wording

The program page says that from 1 July 2026 the work must be finished and the application received within 18 months of the permit's issue date, up from 12. The online form, read the same day, still asks you to acknowledge that the work must be completed within one year of the permit, failing which the City shall deny the application.

Until the two agree, finish inside a year, or email protectiveplumbing@ottawa.ca and ask which applies to your permit.

Do backwater valves require maintenance?

Yes, and it is the owner's job. The City's FAQ says to maintain the valve to the manufacturer's directions, periodically or before a forecast heavy rainfall, so that it is free of debris, works, and has its cleanout caps and access covers firmly secured. If you cannot do that yourself, it suggests a licensed plumber's inspection.

The City's flood prevention page adds one Ottawa warning. In older homes, especially those with cast iron pipes, rust can build up at the hinge and stop the valve closing during a surcharge. Its causes page lists a clogged backwater valve among the reasons a lateral backs up into a basement.

The rebate form spells out what the City will not answer for: a valve that fails from poor maintenance, poor installation, later changes, power cuts, or an owner who never told the next owner what upkeep it needs. If you sell, pass on the manufacturer's instructions.

When the alarm sounds

Some valves carry an alarm. The FAQ says it means the gate has closed and is doing its job, and that water from inside the house cannot leave while it is shut. Do not shower, flush toilets or wash clothes until the alarm stops and the valve reopens.

What a backwater valve will not stop

The City's FAQ says a properly installed and maintained device keeps out water from a sewer surcharge. It lists what it does not stop:

  • Cracks in walls or window wells.
  • Failed foundation drains or sump pumps.
  • Overflowing eavestroughs and plugged downspouts.
  • Poor foundation drainage or poor lot drainage.
  • Water sources inside the house.

If water is coming in now, our guide on what to do in a plumbing emergency in Ottawa covers the first minutes.

Is a backflow preventer the same as a backwater valve?

No. A backwater valve sits on the sewer pipe leaving the house. A backflow preventer protects the drinking water supply coming in. The City's premise isolation page says those devices are required for industrial, commercial, institutional and large multi-residential properties rated severe or moderate risk under CSA B64.10, mandated by Water By-law 2019-74, schedule "I", and registered with the City's Backflow Prevention Program.

Two of the ten results on page 1 for this search are about that water program.

What to ask a plumber

  1. Which laterals does my house have, sanitary, storm or combined, and where do my foundation drains go?
  2. Is there a valve already? If so, does it need cleaning rather than replacing?
  3. Will the new valve be normally open, inside the dwelling unit, and reachable for maintenance, as the permit inspection requires?
  4. Will you pull the building permit, and who prepares the dimensioned plans and the Schedule 1?
  5. Which program line does this device fall under, and is my house old enough for it?
  6. Will the invoice itemize the valve, the permit and the rest of the work, so it can go with the rebate application?
  7. Have you worked to the City's Sewer Design Guidelines, sections 4.4.5 (sanitary backwater valves), 5.7.5 (service connection hydraulics) and 5.7.7 (storm backwater valves), and its standard drawings S14, S14.1 and S14.2? The FAQ names all of them and says copies come from StandardsSection@ottawa.ca.
  8. How do I maintain this model, and how often?

Our checklist on how to vet a contractor before you hire covers the licence and insurance questions.

Who owns the pipe the valve sits on

The City's sewer lateral page splits it at the property line. The City is responsible for the sanitary and storm laterals from the property line to the street, and the homeowner from the property line to the house. Responsibility may be shared where a lateral needing repair crosses the line. The valve is on your side, and so is its upkeep.

Ottawa plumbers you can start a shortlist from

The City's rebate starts with a licensed professional and a permit. Here are the plumbers in this directory carrying a rating we can source, with the platform it came from, the date it was checked, and the areas each one lists.

  1. Mr. Rooter Plumbing of Ottawa

    4.7 from 1,903 Google reviews, checked 2026-08-19

    Serves Barrhaven, Gloucester, Kanata, Manotick, Nepean, Orléans, Stittsville, Westboro, Richmond

  2. Flash Rooter Drain Cleaning

    5.0 from 500 Google reviews, checked 2026-11-12

    Serves Stittsville

  3. B&W Plumbing

    5.0 from 209 Google reviews, checked 2026-08-19

    Serves Kanata, Barrhaven, Orléans, Nepean, Westboro, Gloucester, Stittsville, Manotick

  4. Canada Plumbing

    5.0 from 176 Google reviews, checked 2026-11-02

    Serves Barrhaven, Kanata, Manotick, Orléans, Richmond, Stittsville

  5. JD Swallow Heating & Cooling

    4.9 from 1,466 Google reviews, checked 2026-08-14

  6. The Super Plumber - Ottawa

    4.9 from 465 Google reviews, checked 2026-08-19

    Serves Barrhaven, Gloucester, Kanata, Manotick, Nepean, Orléans

  7. Braden Foundation Construction

    5.0 from 105 Google reviews, checked 2026-08-14

  8. Cambridge Comfort Home Service Inc.

    4.9 from 158 Google reviews, checked 2026-08-14

    Serves Manotick

That is the top 8 of 32 Ottawa plumbers in this directory carrying a sourced rating. Only listings whose rating carries a source appear here. No business pays for a listing. Claimed listings, the ones a business maintains itself, rank first, and the rest of the order is published on the methodology page. See all of them on Plumbers in Ottawa.

Common questions

Does Ottawa require a backwater valve?

In new homes, yes. The City's building permit page says all new single, semi-detached, row house and townhome dwelling units in Ottawa require a backwater valve on the sanitary service lateral. The City's rebate FAQ says backwater valves were mandatory in new homes after 2004 for the storm line and after 2012 for the sanitary line.

For an existing house, the City's route is a voluntary rebate program that pays toward adding one.

How much does the City of Ottawa give for a backwater valve?

Up to $1,000 for an indoor sanitary backwater valve, $1,000 for an indoor storm backwater valve and $2,500 for an outdoor storm backwater valve, plus 100 per cent of the plumbing-only building permit fee, under the Residential Protective Plumbing program as read on 12 November 2026.

The City pays the lesser of the maximum and the cost of the work. The sanitary rebate needs a house built before 1 January 2012 and the storm rebates a house built before 1 January 2004.

Do I need a permit to install a backwater valve in Ottawa?

Yes. The City's program FAQ and its July 2026 advisory both say a building permit is required to install a protective plumbing device. The application needs legible plans drawn to scale, dimensioned floor plans for every storey in the work, the device's location, type, make and model, and a completed Schedule 1 for designer information.

The City's fee schedule lists a plumbing-only permit at $117 per application, and the program refunds that fee in full for an eligible device.

Does the rebate cover replacing an old backwater valve?
No. The program page says rebates are not available for maintenance, repair or replacement of existing protective plumbing devices, and the application form repeats that it applies regardless of the device's condition. A device the City installed does not qualify either.
What should I not do when the backwater valve alarm goes off?
Do not shower, flush toilets or run the washing machine. The City's FAQ explains that the alarm means the valve has closed against the sewer, so water from inside the house cannot leave either. Resume normal use once the alarm stops and the valve is no longer engaged.
Who is responsible for the sewer pipe to my house?
The City of Ottawa is responsible for the sanitary and storm laterals from the property line to the street, and the homeowner from the property line to the house. The City says responsibility may be shared if a lateral that needs repair crosses the property line. A backwater valve sits on the homeowner's part.
How much does a backwater valve cost to install in Ontario?
No provincial or City body publishes an installation price, and this guide does not quote one. What the City does publish is what it pays back on an eligible house: up to $1,000 for an indoor sanitary valve and the full plumbing-only permit fee. Ask each plumber to quote the valve, the concrete work and the permit as separate lines, because the rebate application needs a paid, itemized invoice.

Compare Ottawa plumbers with sourced ratings and service areas.

Browse plumbers in Ottawa

For homeowners

Adding a backwater valve in Ottawa? Pull the permit before the concrete comes up.

See Ottawa plumbers with sourced public ratings, then check your house's build year against the City's rebate dates and keep every receipt for the application.